FERROCON RUST CONVERTER

What Ferrocon does:

Rust remover

Ferrocon is a revolutionary product that leaves any conventional product with the same application in its shadow. Ferrocon is a simple, economical, long lasting and safe rust converter for iron and steel. Ferrocon creates an extremely hard phosphate coating on the surface of the metal, which attaches not only on the surface, but also nestles itself into the micro pores and hairline cracks.

Primer

When ferrocon is applied, the coating is also a protective barrier, when compared to traditional primers, Ferrocon has an extremely long adhesion to the finish coating. Therefore, Ferrocon is of great value in the fight against and prevention of future rust and future rust growth.

The primer is created by exchange of ions with the metal and forms a barrier for corrosive elements such as water, oxygen, acids, etc. Ferrocon forms a protective layer so we have the perfect primer for any coating (except zinc) which is needed to protect the metal from moisture to prevent rust.

Ferrocon will keep the surface of the metal rust free for several weeks (depending on its environment), before a new  coating needs to be applied.

How Ferrocon works:

Ferrocon leaves behind an extraordinary steel-hardend permanent coating, that can never break, peel nor crack. It also nests itself in the micro-pores and veins of the metal and because it has a 4x lower viscosity than water, the rusting process can never startup again from the inside out.

By exchanging ions the primer becomes in cohesion with the metal, creating a barrier against corrosive elements like water with sea salt. Ferrocon is resistant to sea salt, the coating will be more durable because of it.

Note: on new iron and steel Ferrocon forms a protective layer. This is perfect for iron railings, wrought iron, storage tanks, fuel tanks, vertical surfaces and liquid containers that need protection during transport or long-term storage.

How to use Ferrocon:

Ferrocon can be used on both steel and iron new and old.

Before starting the application, the surface of the metal must be free of obstructing materials such as grease, oil, paint or other covering materials. Also remove loose rust parts. Then apply Ferrocon where it is required. Nu need for grinding or sandblasting.

Ferrocon can be applied on a surface temperature between 59° F and 176° F.

Ferrocon can be applied with a brush, paint roller, low pressure sprayer or in a dip tank.

Note: avoid (rain) water during the application and drying process, except if a bare-steel is required, without the steel-hardened coating. To create a bare clean steel, apply Ferrocon, wait until the reaction is done (approx. one minute), then rinse off with water. Repeat this process when required.

Note: 1 part Ferrocon (possibly used in dip tank) with 20 parts of water, makes an excellent fertilizer for home and garden plants.

For more information about rust removal, please click here.

• Ferrocon application instruction

  Application

  • Before application, the surface of the metal must be free of obstructing materials as grease, oil, paint or other obstructing materials. Remove loose parts of rust, no need for sandblasting or grinding the metal.
  • During the drying process, avoid rain/water washing away the Ferrocon unless you wants a clean bare metal rather than the a protected later. Should this occur unwantedly, a second application could be necessary.
  • Ferrocon can be diluted with water. However, the reaction time will be slowed down.

  Note: In order to speed up the de-rusting process, you can heating Ferrocon up in a dip-tank to a max. 176° Fahrenheit. This will dramatically accelerate the reaction time and speed up the whole process.

  Dip tank:

  Ferrocon is ideal in a dip-tank, because the solution can be used over and over again. Not a single spot of rust will remain with this method. Any moving parts such as screw-thread, couplings etc., rinse or wipe off after application. Ferrocon does not react with rubber, so no worries there.

  Note: No need to throw away after prolonged use; dilute Ferrocon with water; 1 part Ferrocon to 20 water and you’ll have an excellent fertilizer for your home and garden plants.

  Ferrocon achieves reliable and deep rust conversion, minimizing risks of incomplete rust conversion on even the most compromised surfaces.

   

  Ferrocon loosens rusted screws quickly.

  Ferrocon and salts:

  Ferrocon is especially recommended for steel which will come in contact with salt, brine water, seawater, etc. Vessels such as, containers, bridges, pipelines, oil rigs, offshore oil derricks and other offshore structures. Ferrocon is an excellent tool for removing rust. Metal parts can be dipped into Ferrocon without damaging rubber or plastic washers, gaskets or membranes.

Use how much Ferrocon:

1 liter of Ferroccon is sufficient for an average of 88 ft².

Also see our frequently asked questions. 

ORDER FERROCON NOW!

Ferrocon can be used on:

• Steel
• Cast iron
• Stainless steel (wash clean)
• Concrete (rust stain remover)
• Copper (corrosion remover)
• Glass and Enamel (lime and other pollution remover
• Dip tank (the Ferrocon solution can be used multiple times).

Ferrocon can be used for:

• Pipes (rust removal, priming and flushing the inside)
• Wheel rims
• Cast iron stoves
• Reinforcing and structural steel
• Old-timer cars
• And much much more…

Do you have any questions?

Would you like advice about this product? Our expert customer service is there for you!

We are available on working days between 09:00 – 17:00.

ORDER FERROCON NOW!